High efficiency - Using synchronous rectification, full load efficiency exceeds 95%. IP43 protection - When installed with the screw terminals oriented downwards. Screw terminals - No special tools needed for installation.
Completely encapsulated: waterproof, shockproof and ignition protected
The Battery Switch ON/OFF 275A is suitable for battery systems up to 48V. It has a unique ergonomic and aesthetic knob design. The knob is removable for isolation or safety purposes.
The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
Diode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system.
This Battery Combiner Kit is for adding a 2nd or 3rd battery system in your car, boat, RV or any other vehicle. It utilizes the simplest and most advanced technology to keep all your batteries charged using the engine's electrical system.
The smallBMS can replace the VE.Bus BMS in several applications. The smallBMS is intended for use with Victron Smart LiFePo4 batteries with M8 circular connectors.
Argodiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together.
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
The Battery Balancer equalizes the state of charge of two series connected 12V batteries, or of several parallel strings of series connected batteries
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch.
Similarly to Argodiode battery isolators, Argofet isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together.
The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.
The VE.Bus BMS V2 is a Battery Management System (BMS) designed to interface with and protect a single, or multiple Victron Lithium Battery Smart 12,8V & 25,6V (LiFePO4 or LFP) in systems that have Victron inverters or inverter/chargers with VE.Bus communication. It monitors and protects the batteries against over voltage and under voltage of any individual cell, and also over temperature or under temperature conditions.
The BMV-700 is a high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery.
For use in dual battery systems in vehicles/on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored/programmed via Bluetooth, remotely controlled via a remote on/off switch and has an engine running detection mechanism.
The Smart BMS CL 12/100 is a Battery Management system for Victron lithium-iron-phosphate (LiFePO4) Smart Batteries. It has been specifically designed for 12V systems with a 12V alternator.
The essential function of BMV-702 battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery.
The essential function of BMV-702 (Black) battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery.
The SuperPack batteries are extremely easy to install, not needing any additional components.The internal switch will disconnect the battery in case of over discharge, over charge or high temperature.
With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance.
This all-in-one Battery Management System, Current Limiter, Battery Combiner and Battery Protector is a robust and compact solution, specifically designed for 12V systems with 12V alternators, such as vehicles and boats.
For use in dual battery systems in vehicles/on boats where the alternator and the start battery are used to charge the service battery. The unit can be monitored/programmed via Bluetooth and can be remotely controlled via a remote on/off switch.
The Smart BMS 12/200 is an all-in-one Battery Management system for Victron Lithium-Iron-Phosphate (LiFePO4) Smart Batteries. It has been specifically designed for 12V systems with a 12V alternator such as in vehicles and boats.
The Cyrix Battery Combiner is a microprocessor controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a pre-set voltage, and disconnects when the voltage decreases below float level.
The deep cycle AGM telecom series has been designed for telecom applications; excellent 'floor space savers' for marine and vehicle applications
The AGM range has very low internal resistance making them particularly suitable for high current discharge applications such as for inverters, thrusters and winches.
Replacing the active material of the negative plate by a lead carbon composite potentially reduces sulfation and improves charge acceptance of the negative plate.
Models: 12 / 24 Volt
