Victron Energy VE.Direct to global remote interface

When the Interface 1140 is connected to the alternator AC it can measure ripple/frequency.

The VE.Direct to VE.CAN interface cable can be used to make BMV-700 information available on a VE.Can network. Where it can be read by a Color Control GX for example.

The clamp connector with fuse is an accessory for the Blue Smart IP65 Chargers.

This Wall Mount will be especially useful if you like to keep your smart charger handy - above your workshop bench, for example. Now the charger can be used without even moving it!

The IP65 Charger is already protected against dust, and water spray - now you can protect it from accidental damage too. This rubber bumper allows it to withstand the knocks and bangs of workshop life.

The M6/M8 eyelet connector with fuse is an accessory for the Blue Smart IP65 Charger with DC connector.

A cable to connect the BMV shunt to the BMV head unit. A RJ12 cable ships standard with a BMV battery monitor, but if this cable is too long or too short it can be replaced by one of these cables, lengths available from 0.3 up to 30 meters.

A cable to connect Digital Multi Control, Phoenix Inverter Control, Interface MK3-USB, VE.Bus connections between multiple VE.Bus devices and to make VE.Bus and VE.Can connections to a GX device.

Besides an assortment of ANL, MIDI and MEGA fuses, we feature three different types of fuse holders, Simple single fuse holders, a six-way fuse holder and modular single fuse holders.

Some of the USB plugs on our cables are too long to fit in the Wall mount box with a Color Control GX. Use this USB extension cable. Available in 0,3 m length.

The 2 meter extension cable is an accessory of the Blue Smart IP65 Charger with DC connector.

The VE.Direct TX digital output cable can be used in combination with the BlueSolar and SmartSolar MPPT chargers. It supports the following applications:

The VE.Can RJ45 terminator comes in a bag of two when ordered separately. The terminators are also included with some products, for example with the CANUSB.

Temperature Sensor for BlueSolar PWM-Pro

With the BlueSolar PWM-Pro to USB interface cable you can connect the BlueSolar PWM-Pro to your computer.

The 12V cigarette lighter plug, with fuse, is an accessory for the Blue Smart IP65 Charger with DC connector. With this plug you can charge your vehicle battery via the cigarette lighter socket.

The Battery Indicator Eyelet M8 is an accessory for the Blue Smart IP65 Chargers.

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Please check our pricelist for all available models.

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. There are two types, A and B. See the manual for details on which cable to use for which brand of batteries.

The GX Touch 50 & 70 protection cover prevents damage from UV light during prolonged exposure to the sun.

DIN-Rail adapter to easily mount a device on a DIN-Rail. Suitable for the Cerbo GX.

This splitter is used to connect the MultiPlus 500VA - 1600VA range in parallel and 3 phase configurations, or in other installations where multiple VE.Bus ports are required.

Use this cable to connect the (discontinued) Phoenix Inverter 12/180, 24/180, 12/350 or 24/350 to a VE.Bus BMS or a BlueSolar MPPT Charger that features a load output

Use this cable to remotely control BlueSolar and SmartSolar MPPT charge controller models.

The cable translates the remote on/off driver logic from the VE.Bus BMS (normally high, and open circuit in case of alarm) to the logic needed by above products: active pull down to switch off.

A cable to connect the BMV shunt to the BMV head unit. A RJ12 cable ships standard with a BMV battery monitor, lengths available from 0.3 up to 30 meters.

The Orion-Tr DC-DC Charger Isolated remote cable is intended for applications where the remote on/off signal is referenced to the secondary battery (e.g. lithium battery with BMS).

The battery indicator panel shows the state of charge of the battery. It is an accessory for the Blue Smart IP65 Chargers.