Victron Energy RJ12 UTP Cable

A cable to connect the BMV shunt to the BMV head unit. A RJ12 cable ships standard with a BMV battery monitor, but if this cable is too long or too short it can be replaced by one of these cables, lengths available from 0.3 up to 30 meters.

Victron Energy RJ45 UTP Cable

A cable to connect Digital Multi Control, Phoenix Inverter Control, Interface MK3-USB, VE.Bus connections between multiple VE.Bus devices and to make VE.Bus and VE.Can connections to a GX device.

Victron Energy USB extension cable one side right angle

Some of the USB plugs on our cables are too long to fit in the Wall mount box with a Color Control GX. Use this USB extension cable. Available in 0,3 m length.

Victron Energy VE.Direct TX digital output cable

The VE.Direct TX digital output cable can be used in combination with the BlueSolar and SmartSolar MPPT chargers. It supports the following applications:

Victron Energy BlueSolar PWM-Pro to USB interface cable

With the BlueSolar PWM-Pro to USB interface cable you can connect the BlueSolar PWM-Pro to your computer.

Victron Energy VE.Direct cable

The VE.Direct cable is available in different lengths. There is a straight and 90 degree angle model. Please check our pricelist for all available models.

Victron Energy VE.Can to CAN-bus BMS cable

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. There are two types, A and B. See the manual for details on which cable to use for which brand of batteries.

Victron Energy RJ45-splitter 1xRJ45 male/15cm cable/2xRJ45 female

This splitter is used to connect the MultiPlus 500VA - 1600VA range in parallel and 3 phase configurations, or in other installations where multiple VE.Bus ports are required.

Victron Energy Inverting remote on-off cable

Use this cable to connect the (discontinued) Phoenix Inverter 12/180, 24/180, 12/350 or 24/350 to a VE.Bus BMS or a BlueSolar MPPT Charger that features a load output

Victron Energy VE.Direct non inverting remote on/off cable

Use this cable to remotely control BlueSolar and SmartSolar MPPT charge controller models.

Victron Energy Non inverting remote on-off cable

The cable translates the remote on/off driver logic from the VE.Bus BMS (normally high, and open circuit in case of alarm) to the logic needed by above products: active pull down to switch off.

Victron Energy Cable for Smart BMS CL 12/100 to MultiPlus

A cable to connect the BMV shunt to the BMV head unit. A RJ12 cable ships standard with a BMV battery monitor, lengths available from 0.3 up to 30 meters.

Victron Energy Orion-Tr DC-DC Charger Isolated remote cable

The Orion-Tr DC-DC Charger Isolated remote cable is intended for applications where the remote on/off signal is referenced to the secondary battery (e.g. lithium battery with BMS).

Victron Energy M8 circular connector Male/Female 3 pole cable

This cable can be used to extend the BMS communication cables between a Lithium Battery Smart and the BMS. It ships in a bag of 2 pieces and is available in 1, 2, 3 and 5 m lengths.

Victron Energy Skylla-i remote on-off cable

Use this cable to connect a Skylla-i to a VE.Bus BMS. The VE.Bus BMS will then disable the Skylla-i charger when the batteries are fully charged.

Victron Energy Bus to BMS 12-200 alternator control cable

Victron Energy Bus to BMS 12-200 alternator control cable

Victron Energy VE.Can Power Cable

When the CAN bus is not powered by a Skylla-I or an MPPT, you will need the new VE.Can Power Cable to supply the power.

Victron Energy VE.Can to NMEA 2000 micro-C male cable

Use this cable to connect a Victron product with a VE.Can port to a NMEA 2000 network.

Victron Energy Shore Power Cable

Waterproof IP 56 shore power cable and inlet; Moulded plug and connector; Power indication LED; Protection cap on female connector; Stainless steel or Polyamide inlet