The CAN-bus Temp. Sensor is a battery temperature sensor for the Buck-Boost DC/DC converter range and is an essential accessory when the Buck-Boost DC/DC converter is connected to a LFP lithium battery.
VE.Direct to RS232 interface
When the Interface 1140 is connected to the alternator AC it can measure ripple/frequency.
The VE.Direct to VE.CAN interface cable can be used to make BMV-700 information available on a VE.Can network. Where it can be read by a Color Control GX for example.
The clamp connector with fuse is an accessory for the Blue Smart IP65 Chargers.
This Wall Mount will be especially useful if you like to keep your smart charger handy - above your workshop bench, for example. Now the charger can be used without even moving it!
The IP65 Charger is already protected against dust, and water spray - now you can protect it from accidental damage too. This rubber bumper allows it to withstand the knocks and bangs of workshop life.
The M6/M8 eyelet connector with fuse is an accessory for the Blue Smart IP65 Charger with DC connector.
The 2 meter extension cable is an accessory of the Blue Smart IP65 Charger with DC connector.
The VE.Direct TX digital output cable can be used in combination with the BlueSolar and SmartSolar MPPT chargers. It supports the following applications:
The VE.Can RJ45 terminator comes in a bag of two when ordered separately. The terminators are also included with some products, for example with the CANUSB.
Temperature Sensor for BlueSolar PWM-Pro
With the BlueSolar PWM-Pro to USB interface cable you can connect the BlueSolar PWM-Pro to your computer.
The 12V cigarette lighter plug, with fuse, is an accessory for the Blue Smart IP65 Charger with DC connector. With this plug you can charge your vehicle battery via the cigarette lighter socket.
The Battery Indicator Eyelet M8 is an accessory for the Blue Smart IP65 Chargers.
The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.
The GX Touch 50 & 70 protection cover prevents damage from UV light during prolonged exposure to the sun.
DIN-Rail adapter to easily mount a device on a DIN-Rail. Suitable for the Cerbo GX.
Use this cable to connect the (discontinued) Phoenix Inverter 12/180, 24/180, 12/350 or 24/350 to a VE.Bus BMS or a BlueSolar MPPT Charger that features a load output
Use this cable to remotely control BlueSolar and SmartSolar MPPT charge controller models.
A cable to connect the BMV shunt to the BMV head unit. A RJ12 cable ships standard with a BMV battery monitor, lengths available from 0.3 up to 30 meters.
The Orion-Tr DC-DC Charger Isolated remote cable is intended for applications where the remote on/off signal is referenced to the secondary battery (e.g. lithium battery with BMS).
The battery indicator panel shows the state of charge of the battery. It is an accessory for the Blue Smart IP65 Chargers.
The MPPT WireBox provides an extra level of safety, and is particularly useful if your MPPT Solar Charger is installed in a general access area. It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws.
Spare battery temperature sensor for the Inverter RS Smart Solar.
Victron Energy Temperature sensor Quattro, MultiPlus and GX Device
This adapter is designed to easily replace the CCGX display with the newer GX Touch. Contents of the packaging are the metal bracket, the plastic bezel, and four mounting screws.
Wall mount enclosure for 65 x 120mm GX panels.
RS485 to USB interface, available in 1.8 m and 5 m.
Smart and professional; this new snap shut carry case provides protective stowage and easy transport for your Blue Smart IP65 charger, and its accessories.
